Recent Darwin versions place contraints on the use of run paths
specified in environment variables.  This breaks some assumptions
in the GCC build.

This change allows the user to configure a Darwin build to use
'@rpath/libraryname.dylib' in library names and then to add an
embedded runpath to executables (and libraries with dependents).

The embedded runpath is added by default unless the user adds
'-nodefaultrpaths' to the link line.

For an installed compiler, it means that any executable built with
that compiler will reference the runtimes installed with the
compiler (equivalent to hard-coding the library path into the name
of the library).

During build-time configurations  any "-B" entries will be added to
the runpath thus the newly-built libraries will be found by exes.

Since the install name is set in libtool, that decision needs to be
available here (but might also cause dependent ones in Makefiles,
so we need to export a conditional).

This facility is not available for Darwin 8 or earlier, however the
existing environment variable runpath does work there.

We default this on for systems where the external DYLD_LIBRARY_PATH
does not work and off for Darwin 8 or earlier.  For systems that can
use either method, if the value is unset, we use the default (which
is currently DYLD_LIBRARY_PATH).

ChangeLog:

	* configure: Regenerate.
	* configure.ac: Do not add default runpaths to GCC exes
	when we are building -static-libstdc++/-static-libgcc (the
	default).
	* libtool.m4: Add 'enable-darwin-at-runpath'.  Act  on the
	enable flag to alter Darwin libraries to use @rpath names.

gcc/ChangeLog:

	* aclocal.m4: Regenerate.
	* configure: Regenerate.
	* configure.ac: Handle Darwin rpaths.
	* config/darwin.h: Handle Darwin rpaths.
	* config/darwin.opt: Handle Darwin rpaths.
	* Makefile.in:  Handle Darwin rpaths.

gcc/ada/ChangeLog:

	* gcc-interface/Makefile.in: Handle Darwin rpaths.

gcc/jit/ChangeLog:
	* Make-lang.in: Handle Darwin rpaths.

libatomic/ChangeLog:

	* Makefile.am: Handle Darwin rpaths.
	* Makefile.in: Regenerate.
	* configure: Regenerate.
	* configure.ac: Handle Darwin rpaths.

libbacktrace/ChangeLog:

	* configure: Regenerate.
	* configure.ac: Handle Darwin rpaths.

libcc1/ChangeLog:

	* configure: Regenerate.

libffi/ChangeLog:

	* Makefile.am: Handle Darwin rpaths.
	* Makefile.in: Regenerate.
	* configure: Regenerate.

libgcc/ChangeLog:

	* config/t-slibgcc-darwin: Generate libgcc_s
	with an @rpath name.
	* config.host: Handle Darwin rpaths.

libgfortran/ChangeLog:

	* Makefile.am: Handle Darwin rpaths.
	* Makefile.in: Regenerate.
	* configure: Regenerate.
	* configure.ac: Handle Darwin rpaths

libgm2/ChangeLog:

	* Makefile.am: Handle Darwin rpaths.
	* Makefile.in: Regenerate.
	* aclocal.m4: Regenerate.
	* configure: Regenerate.
	* configure.ac: Handle Darwin rpaths.
	* libm2cor/Makefile.am: Handle Darwin rpaths.
	* libm2cor/Makefile.in: Regenerate.
	* libm2iso/Makefile.am: Handle Darwin rpaths.
	* libm2iso/Makefile.in: Regenerate.
	* libm2log/Makefile.am: Handle Darwin rpaths.
	* libm2log/Makefile.in: Regenerate.
	* libm2min/Makefile.am: Handle Darwin rpaths.
	* libm2min/Makefile.in: Regenerate.
	* libm2pim/Makefile.am: Handle Darwin rpaths.
	* libm2pim/Makefile.in: Regenerate.

libgomp/ChangeLog:

	* Makefile.am: Handle Darwin rpaths.
	* Makefile.in: Regenerate.
	* configure: Regenerate.
	* configure.ac: Handle Darwin rpaths

libitm/ChangeLog:

	* Makefile.am: Handle Darwin rpaths.
	* Makefile.in: Regenerate.
	* configure: Regenerate.
	* configure.ac: Handle Darwin rpaths.

libobjc/ChangeLog:

	* configure: Regenerate.
	* configure.ac: Handle Darwin rpaths.

libphobos/ChangeLog:

	* configure: Regenerate.
	* configure.ac: Handle Darwin rpaths.
	* libdruntime/Makefile.am: Handle Darwin rpaths.
	* libdruntime/Makefile.in: Regenerate.
	* src/Makefile.am: Handle Darwin rpaths.
	* src/Makefile.in: Regenerate.

libquadmath/ChangeLog:

	* Makefile.am: Handle Darwin rpaths.
	* Makefile.in: Regenerate.
	* configure: Regenerate.
	* configure.ac: Handle Darwin rpaths.

libsanitizer/ChangeLog:

	* asan/Makefile.am: Handle Darwin rpaths.
	* asan/Makefile.in: Regenerate.
	* configure: Regenerate.
	* hwasan/Makefile.am: Handle Darwin rpaths.
	* hwasan/Makefile.in: Regenerate.
	* lsan/Makefile.am: Handle Darwin rpaths.
	* lsan/Makefile.in: Regenerate.
	* tsan/Makefile.am: Handle Darwin rpaths.
	* tsan/Makefile.in: Regenerate.
	* ubsan/Makefile.am: Handle Darwin rpaths.
	* ubsan/Makefile.in: Regenerate.

libssp/ChangeLog:

	* Makefile.am: Handle Darwin rpaths.
	* Makefile.in: Regenerate.
	* configure: Regenerate.
	* configure.ac: Handle Darwin rpaths.

libstdc++-v3/ChangeLog:

	* configure: Regenerate.
	* configure.ac: Handle Darwin rpaths.
	* src/Makefile.am: Handle Darwin rpaths.
	* src/Makefile.in: Regenerate.

libvtv/ChangeLog:

	* configure: Regenerate.
	* configure.ac: Handle Darwin rpaths.

lto-plugin/ChangeLog:
	* configure: Regenerate.
	* configure.ac: Handle Darwin rpaths.

zlib/ChangeLog:
	* configure: Regenerate.
	* configure.ac: Handle Darwin rpaths.

This reports common symbols like GNU nm, via a type code of 'C'.

ChangeLog:

	* libtool.m4 (lt_cv_sys_global_symbol_pipe): Augment symcode for
	Solaris 11.

gcc/ChangeLog:

	* configure: Regenerate.

libatomic/ChangeLog:

	* configure: Regenerate.

libbacktrace/ChangeLog:

	* configure: Regenerate.

libcc1/ChangeLog:

	* configure: Regenerate.

libffi/ChangeLog:

	* configure: Regenerate.

libgfortran/ChangeLog:

	* configure: Regenerate.

libgm2/ChangeLog:

	* configure: Regenerate.

libgomp/ChangeLog:

	* configure: Regenerate.

libitm/ChangeLog:

	* configure: Regenerate.

libobjc/ChangeLog:

	* configure: Regenerate.

libphobos/ChangeLog:

	* configure: Regenerate.

libquadmath/ChangeLog:

	* configure: Regenerate.

libsanitizer/ChangeLog:

	* configure: Regenerate.

libssp/ChangeLog:

	* configure: Regenerate.

libstdc++-v3/ChangeLog:

	* configure: Regenerate.

libvtv/ChangeLog:

	* configure: Regenerate.

lto-plugin/ChangeLog:

	* configure: Regenerate.

zlib/ChangeLog:

	* configure: Regenerate.

These are the os support patches we have been grooming and maintaining
for quite a few years over on git.haiku-os.org.  All of these
architectures are working and most have been stable for quite some time.

ChangeLog:

	* configure: Regenerate.
	* configure.ac: Add Haiku to list of ELF OSes
	* libtool.m4: Update sys_lib_dlsearch_path_spec on Haiku.

gcc/ChangeLog:

	* configure: Regenerate.

libatomic/ChangeLog:

	* configure: Regenerate.

libbacktrace/ChangeLog:

	* configure: Regenerate.

libcc1/ChangeLog:

	* configure: Regenerate.

libffi/ChangeLog:

	* configure: Regenerate.

libgfortran/ChangeLog:

	* configure: Regenerate.

libgm2/ChangeLog:

	* configure: Regenerate.

libgomp/ChangeLog:

	* configure: Regenerate.

libitm/ChangeLog:

	* configure: Regenerate.

libobjc/ChangeLog:

	* configure: Regenerate.

libphobos/ChangeLog:

	* configure: Regenerate.

libquadmath/ChangeLog:

	* configure: Regenerate.

libsanitizer/ChangeLog:

	* configure: Regenerate.

libssp/ChangeLog:

	* configure: Regenerate.

libstdc++-v3/ChangeLog:

	* configure: Regenerate.

libvtv/ChangeLog:

	* configure: Regenerate.

lto-plugin/ChangeLog:

	* configure: Regenerate.

zlib/ChangeLog:

	* configure: Regenerate.

My previous nm patch handled all cases but one -- if the user set NM in
the environment to a path which contained an option, libtool's nm
detection tries to run nm against a copy of nm with the options in it:
e.g. if NM was set to "nm --blargle", and nm was found in /usr/bin, the
test would try to run "/usr/bin/nm --blargle /usr/bin/nm --blargle".
This is unlikely to be desirable: in this case we should run
"/usr/bin/nm --blargle /usr/bin/nm".

Furthermore, as part of this nm has to detect when the passed-in $NM
contains a path, and in that case avoid doing a path search itself.
This too was thrown off if an option contained something that looked
like a path, e.g. NM="nm -B../prev-gcc"; libtool then tries to run
"nm -B../prev-gcc nm" which rarely works well (and indeed it looks
to see whether that nm exists, finds it doesn't, and wrongly concludes
that nm -p or whatever does not work).

Fix all of these by clipping all options (defined as everything
including and after the first " -") before deciding whether nm
contains a path (but not using the clipped value for anything else),
and then removing all options from the path-modified nm before
looking to see whether that nm existed.

NM=my-nm now does a path search and runs e.g.
  /usr/bin/my-nm -B /usr/bin/my-nm

NM=/usr/bin/my-nm now avoids a path search and runs e.g.
  /usr/bin/my-nm -B /usr/bin/my-nm

NM="my-nm -p../wombat" now does a path search and runs e.g.
  /usr/bin/my-nm -p../wombat -B /usr/bin/my-nm

NM="../prev-binutils/new-nm -B../prev-gcc" now avoids a path search:
  ../prev-binutils/my-nm -B../prev-gcc -B ../prev-binutils/my-nm

This seems to be all combinations, including those used by GCC bootstrap
(which, before this commit, fails to bootstrap when configured
--with-build-config=bootstrap-lto, because the lto plugin is now using
--export-symbols-regex, which requires libtool to find a working nm,
while also using -B../prev-gcc to point at the lto plugin associated
with the GCC just built.)

Regenerate all affected configure scripts.

ChangeLog:

	* libtool.m4 (LT_PATH_NM): Handle user-specified NM with
	options, including options containing paths.

gcc/ChangeLog:

	* configure: Regenerate.

libatomic/ChangeLog:

	* configure: Regenerate.

libbacktrace/ChangeLog:

	* configure: Regenerate.

libcc1/ChangeLog:

	* configure: Regenerate.

libffi/ChangeLog:

	* configure: Regenerate.

libgfortran/ChangeLog:

	* configure: Regenerate.

libgm2/ChangeLog:

	* configure: Regenerate.

libgomp/ChangeLog:

	* configure: Regenerate.

libitm/ChangeLog:

	* configure: Regenerate.

libobjc/ChangeLog:

	* configure: Regenerate.

libphobos/ChangeLog:

	* configure: Regenerate.

libquadmath/ChangeLog:

	* configure: Regenerate.

libsanitizer/ChangeLog:

	* configure: Regenerate.

libssp/ChangeLog:

	* configure: Regenerate.

libstdc++-v3/ChangeLog:

	* configure: Regenerate.

libvtv/ChangeLog:

	* configure: Regenerate.

lto-plugin/ChangeLog:

	* configure: Regenerate.

zlib/ChangeLog:

	* configure: Regenerate.

Libtool needs to get BSD-format (or MS-format) output out of the system
nm, so that it can scan generated object files for symbol names for
-export-symbols-regex support.  Some nms need specific flags to turn on
BSD-formatted output, so libtool checks for this in its AC_PATH_NM.
Unfortunately the code to do this has a pair of interlocking flaws:

 - it runs the test by doing an nm of /dev/null.  Some platforms
   reasonably refuse to do an nm on a device file, but before now this
   has only been worked around by assuming that the error message has a
   specific textual form emitted by Tru64 nm, and that getting this
   error means this is Tru64 nm and that nm -B would work to produce
   BSD-format output, even though the test never actually got anything
   but an error message out of nm -B.  This is fixable by nm'ing *nm
   itself* (since we necessarily have a path to it).

 - the test is entirely skipped if NM is set in the environment, on the
   grounds that the user has overridden the test: but the user cannot
   reasonably be expected to know that libtool wants not only nm but
   also flags forcing BSD-format output.  Worse yet, one such "user" is
   the top-level Cygnus configure script, which neither tests for
   nor specifies any BSD-format flags.  So platforms needing BSD-format
   flags always fail to set them when run in a Cygnus tree, breaking
   -export-symbols-regex on such platforms.  Libtool also needs to
   augment $LD on some platforms, but this is done unconditionally,
   augmenting whatever the user specified: the nm check should do the
   same.

   One wrinkle: if the user has overridden $NM, a path might have been
   provided: so we use the user-specified path if there was one, and
   otherwise do the path search as usual.  (If the nm specified doesn't
   work, this might lead to a few extra pointless path searches -- but
   the test is going to fail anyway, so that's not a problem.)

(Tested with NM unset, and set to nm, /usr/bin/nm, my-nm where my-nm is a
symlink to /usr/bin/nm on the PATH, and /not-on-the-path/my-nm where
*that* is a symlink to /usr/bin/nm.)

ChangeLog:

	* libtool.m4 (LT_PATH_NM): Try BSDization flags with a user-provided
	NM, if there is one.  Run nm on itself, not on /dev/null, to avoid
	errors from nms that refuse to work on non-regular files.  Remove
	other workarounds for this problem.  Strip out blank lines from the
	nm output.

fixincludes/ChangeLog:

	* configure: Regenerate.

gcc/ChangeLog:

	* configure: Regenerate.

libatomic/ChangeLog:

	* configure: Regenerate.

libbacktrace/ChangeLog:

	* configure: Regenerate.

libcc1/ChangeLog:

	* configure: Regenerate.

libffi/ChangeLog:

	* configure: Regenerate.

libgfortran/ChangeLog:

	* configure: Regenerate.

libgm2/ChangeLog:

	* configure: Regenerate.

libgomp/ChangeLog:

	* configure: Regenerate.

libitm/ChangeLog:

	* configure: Regenerate.

libobjc/ChangeLog:

	* configure: Regenerate.

libphobos/ChangeLog:

	* configure: Regenerate.

libquadmath/ChangeLog:

	* configure: Regenerate.

libsanitizer/ChangeLog:

	* configure: Regenerate.

libssp/ChangeLog:

	* configure: Regenerate.

libstdc++-v3/ChangeLog:

	* configure: Regenerate.

libvtv/ChangeLog:

	* configure: Regenerate.

lto-plugin/ChangeLog:

	* configure: Regenerate.

zlib/ChangeLog:

	* configure: Regenerate.

AR from older binutils doesn't work with --plugin and rc:

[hjl@gnu-cfl-2 bin]$ touch foo.c
[hjl@gnu-cfl-2 bin]$ ar --plugin /usr/libexec/gcc/x86_64-redhat-linux/10/liblto_plugin.so rc libfoo.a foo.c
[hjl@gnu-cfl-2 bin]$ ./ar --plugin /usr/libexec/gcc/x86_64-redhat-linux/10/liblto_plugin.so rc libfoo.a foo.c
./ar: no operation specified
[hjl@gnu-cfl-2 bin]$ ./ar --version
GNU ar (Linux/GNU Binutils) 2.29.51.0.1.20180112
Copyright (C) 2018 Free Software Foundation, Inc.
This program is free software; you may redistribute it under the terms of
the GNU General Public License version 3 or (at your option) any later version.
This program has absolutely no warranty.
[hjl@gnu-cfl-2 bin]$

Check if AR works with --plugin and rc before passing --plugin to AR and
RANLIB.

ChangeLog:

	* configure: Regenerated.
	* libtool.m4 (_LT_CMD_OLD_ARCHIVE): Check if AR works with
	--plugin and rc before enabling --plugin.

config/ChangeLog:

	* gcc-plugin.m4 (GCC_PLUGIN_OPTION): Check if AR works with
	--plugin and rc before enabling --plugin.

gcc/ChangeLog:

	* configure: Regenerate.

libatomic/ChangeLog:

	* configure: Regenerate.

libbacktrace/ChangeLog:

	* configure: Regenerate.

libcc1/ChangeLog:

	* configure: Regenerate.

libffi/ChangeLog:

	* configure: Regenerate.

libgfortran/ChangeLog:

	* configure: Regenerate.

libgm2/ChangeLog:

	* configure: Regenerate.

libgomp/ChangeLog:

	* configure: Regenerate.

libiberty/ChangeLog:

	* configure: Regenerate.

libitm/ChangeLog:

	* configure: Regenerate.

libobjc/ChangeLog:

	* configure: Regenerate.

libphobos/ChangeLog:

	* configure: Regenerate.

libquadmath/ChangeLog:

	* configure: Regenerate.

libsanitizer/ChangeLog:

	* configure: Regenerate.

libssp/ChangeLog:

	* configure: Regenerate.

libstdc++-v3/ChangeLog:

	* configure: Regenerate.

libvtv/ChangeLog:

	* configure: Regenerate.

lto-plugin/ChangeLog:

	* configure: Regenerate.

zlib/ChangeLog:

	* configure: Regenerate.

Sync with binutils for building binutils with LTO:

50ad1254d50 GCC: Pass --plugin to AR and RANLIB

Detect GCC LTO plugin.  Pass --plugin to AR and RANLIB to support LTO
build.

ChangeLog:

	* Makefile.tpl (AR): Add @AR_PLUGIN_OPTION@
	(RANLIB): Add @RANLIB_PLUGIN_OPTION@.
	* configure.ac: Include config/gcc-plugin.m4.
	AC_SUBST AR_PLUGIN_OPTION and RANLIB_PLUGIN_OPTION.
	* libtool.m4 (_LT_CMD_OLD_ARCHIVE): Pass --plugin to AR and
	RANLIB if possible.
	* Makefile.in: Regenerated.
	* configure: Likewise.

config/ChangeLog:

	* gcc-plugin.m4 (GCC_PLUGIN_OPTION): New.

libiberty/ChangeLog:

	* Makefile.in (AR): Add @AR_PLUGIN_OPTION@
	(RANLIB): Add @RANLIB_PLUGIN_OPTION@.
	(configure_deps): Depend on ../config/gcc-plugin.m4.
	* configure.ac: AC_SUBST AR_PLUGIN_OPTION and
	RANLIB_PLUGIN_OPTION.
	* aclocal.m4: Regenerated.
	* configure: Likewise.

zlib/ChangeLog:

	* configure: Regenerated.

gcc/ChangeLog:

	* configure: Regenerate.

libatomic/ChangeLog:

	* configure: Regenerate.

libbacktrace/ChangeLog:

	* configure: Regenerate.

libcc1/ChangeLog:

	* configure: Regenerate.

libffi/ChangeLog:

	* configure: Regenerate.

libgfortran/ChangeLog:

	* configure: Regenerate.

libgm2/ChangeLog:

	* configure: Regenerate.

libgomp/ChangeLog:

	* configure: Regenerate.

libitm/ChangeLog:

	* configure: Regenerate.

libobjc/ChangeLog:

	* configure: Regenerate.

libphobos/ChangeLog:

	* configure: Regenerate.

libquadmath/ChangeLog:

	* configure: Regenerate.

libsanitizer/ChangeLog:

	* configure: Regenerate.

libssp/ChangeLog:

	* configure: Regenerate.

libstdc++-v3/ChangeLog:

	* configure: Regenerate.

libvtv/ChangeLog:

	* configure: Regenerate.

lto-plugin/ChangeLog:

	* configure: Regenerate.

As discussed in
https://gcc.gnu.org/pipermail/gcc-patches/2023-June/621976.html this
should put the autotools generated files in sync to what they were
generated from (and make an automated checker happy).

Tested by bootstrapping on top of only a few revisions ago.

zlib/ChangeLog:

2023-06-16  Martin Jambor  <mjambor@suse.cz>

	* Makefile.in: Regenerate.
	* configure: Likewise.

gcc/ChangeLog:

2023-06-16  Martin Jambor  <mjambor@suse.cz>

	* configure: Regenerate.

[ This is my third attempt to add this configure option.  The first
version was approved but it came too late in the development cycle.
The second version was also approved, but I had to revert it:
<https://gcc.gnu.org/pipermail/gcc-patches/2022-November/607082.html>.
I've fixed the problem (by moving $(PICFLAG) from INTERNAL_CFLAGS to
ALL_COMPILERFLAGS).  Another change is that since r13-4536 I no longer
need to touch Makefile.def, so this patch is simplified. ]

This patch implements the --enable-host-pie configure option which
makes the compiler executables PIE.  This can be used to enhance
protection against ROP attacks, and can be viewed as part of a wider
trend to harden binaries.

It is similar to the option --enable-host-shared, except that --e-h-s
won't add -shared to the linker flags whereas --e-h-p will add -pie.
It is different from --enable-default-pie because that option just
adds an implicit -fPIE/-pie when the compiler is invoked, but the
compiler itself isn't PIE.

Since r12-5768-gfe7c3ecf, PCH works well with PIE, so there are no PCH
regressions.

When building the compiler, the build process may use various in-tree
libraries; these need to be built with -fPIE so that it's possible to
use them when building a PIE.  For instance, when --with-included-gettext
is in effect, intl object files must be compiled with -fPIE.  Similarly,
when building in-tree gmp, isl, mpfr and mpc, they must be compiled with
-fPIE.

With this patch and --enable-host-pie used to configure gcc:

$ file gcc/cc1{,plus,obj,gm2} gcc/f951 gcc/lto1 gcc/cpp gcc/go1 gcc/rust1 gcc/gnat1
gcc/cc1:     ELF 64-bit LSB pie executable, x86-64, version 1 (GNU/Linux), dynamically linked, interpreter /lib64/ld-linux-x86-64.so.2, BuildID[sha1]=98e22cde129d304aa6f33e61b1c39e144aeb135e, for GNU/Linux 3.2.0, with debug_info, not stripped
gcc/cc1plus: ELF 64-bit LSB pie executable, x86-64, version 1 (GNU/Linux), dynamically linked, interpreter /lib64/ld-linux-x86-64.so.2, BuildID[sha1]=859d1ea37e43dfe50c18fd4e3dd9a34bb1db8f77, for GNU/Linux 3.2.0, with debug_info, not stripped
gcc/cc1obj:  ELF 64-bit LSB pie executable, x86-64, version 1 (GNU/Linux), dynamically linked, interpreter /lib64/ld-linux-x86-64.so.2, BuildID[sha1]=1964f8ecee6163182bc26134e2ac1f324816e434, for GNU/Linux 3.2.0, with debug_info, not stripped
gcc/cc1gm2:  ELF 64-bit LSB pie executable, x86-64, version 1 (GNU/Linux), dynamically linked, interpreter /lib64/ld-linux-x86-64.so.2, BuildID[sha1]=a396672c7ff913d21855829202e7b02ecf42ff4c, for GNU/Linux 3.2.0, with debug_info, not stripped
gcc/f951:    ELF 64-bit LSB pie executable, x86-64, version 1 (GNU/Linux), dynamically linked, interpreter /lib64/ld-linux-x86-64.so.2, BuildID[sha1]=59c523db893186547ac75c7a71f48be0a461c06b, for GNU/Linux 3.2.0, with debug_info, not stripped
gcc/lto1:    ELF 64-bit LSB pie executable, x86-64, version 1 (GNU/Linux), dynamically linked, interpreter /lib64/ld-linux-x86-64.so.2, BuildID[sha1]=084a7b77df7be2d63c2d4c655b5bbc3fcdb6038d, for GNU/Linux 3.2.0, with debug_info, not stripped
gcc/cpp:     ELF 64-bit LSB pie executable, x86-64, version 1 (GNU/Linux), dynamically linked, interpreter /lib64/ld-linux-x86-64.so.2, BuildID[sha1]=3503bf8390d219a10d6653b8560aa21158132168, for GNU/Linux 3.2.0, with debug_info, not stripped
gcc/go1:     ELF 64-bit LSB pie executable, x86-64, version 1 (GNU/Linux), dynamically linked, interpreter /lib64/ld-linux-x86-64.so.2, BuildID[sha1]=988cc673af4fba5dcb482f4b34957b99050a68c5, for GNU/Linux 3.2.0, with debug_info, not stripped
gcc/rust1:   ELF 64-bit LSB pie executable, x86-64, version 1 (GNU/Linux), dynamically linked, interpreter /lib64/ld-linux-x86-64.so.2, BuildID[sha1]=b6a5d3d514446c4dcdee0707f086ab9b274a8a3c, for GNU/Linux 3.2.0, with debug_info, not stripped
gcc/gnat1:   ELF 64-bit LSB pie executable, x86-64, version 1 (GNU/Linux), dynamically linked, interpreter /lib64/ld-linux-x86-64.so.2, BuildID[sha1]=bb11ccdc2c366fe3fe0980476bcd8ca19b67f9dc, for GNU/Linux 3.2.0, with debug_info, not stripped

I plan to add an option to link with -Wl,-z,now.

Bootstrapped on x86_64-pc-linux-gnu with --with-included-gettext
--enable-host-pie as well as without --enable-host-pie.  Also tested
on a Debian system where the system gcc was configured with
--enable-default-pie.

Co-Authored by: Iain Sandoe  <iain@sandoe.co.uk>

ChangeLog:

	* configure.ac (--enable-host-pie): New check.  Set PICFLAG after this
	check.
	* configure: Regenerate.

c++tools/ChangeLog:

	* Makefile.in: Rename PIEFLAG to PICFLAG.  Set LD_PICFLAG.  Use it.
	Use pic/libiberty.a if PICFLAG is set.
	* configure.ac (--enable-default-pie): Set PICFLAG instead of PIEFLAG.
	(--enable-host-pie): New check.
	* configure: Regenerate.

fixincludes/ChangeLog:

	* Makefile.in: Set and use PICFLAG and LD_PICFLAG.  Use the "pic"
	build of libiberty if PICFLAG is set.
	* configure.ac:
	* configure: Regenerate.

gcc/ChangeLog:

	* Makefile.in: Set LD_PICFLAG.  Use it.  Set enable_host_pie.
	Remove NO_PIE_CFLAGS and NO_PIE_FLAG.  Pass LD_PICFLAG to
	ALL_LINKERFLAGS.  Use the "pic" build of libiberty if --enable-host-pie.
	* configure.ac (--enable-host-shared): Don't set PICFLAG here.
	(--enable-host-pie): New check.  Set PICFLAG and LD_PICFLAG after this
	check.
	* configure: Regenerate.
	* doc/install.texi: Document --enable-host-pie.

gcc/ada/ChangeLog:

	* gcc-interface/Make-lang.in (ALL_ADAFLAGS): Remove NO_PIE_CFLAGS.  Add
	PICFLAG.  Use PICFLAG when building ada/b_gnat1.o and ada/b_gnatb.o.
	* gcc-interface/Makefile.in: Use pic/libiberty.a if PICFLAG is set.
	Remove NO_PIE_FLAG.

gcc/m2/ChangeLog:

	* Make-lang.in: New var, GM2_PICFLAGS.  Use it.

gcc/d/ChangeLog:

	* Make-lang.in: Remove NO_PIE_CFLAGS.

intl/ChangeLog:

	* Makefile.in: Use @PICFLAG@ in COMPILE as well.
	* configure.ac (--enable-host-shared): Don't set PICFLAG here.
	(--enable-host-pie): New check.  Set PICFLAG after this check.
	* configure: Regenerate.

libcody/ChangeLog:

	* Makefile.in: Pass LD_PICFLAG to LDFLAGS.
	* configure.ac (--enable-host-shared): Don't set PICFLAG here.
	(--enable-host-pie): New check.  Set PICFLAG and LD_PICFLAG after this
	check.
	* configure: Regenerate.

libcpp/ChangeLog:

	* configure.ac (--enable-host-shared): Don't set PICFLAG here.
	(--enable-host-pie): New check.  Set PICFLAG after this check.
	* configure: Regenerate.

libdecnumber/ChangeLog:

	* configure.ac (--enable-host-shared): Don't set PICFLAG here.
	(--enable-host-pie): New check.  Set PICFLAG after this check.
	* configure: Regenerate.

libiberty/ChangeLog:

	* configure.ac: Also set shared when enable_host_pie.
	* configure: Regenerate.

zlib/ChangeLog:

	* configure.ac (--enable-host-shared): Don't set PICFLAG here.
	(--enable-host-pie): New check.  Set PICFLAG after this check.
	* configure: Regenerate.

This reverts commit 251c72a6.

This patch implements the --enable-host-pie configure option which
makes the compiler executables PIE.  This can be used to enhance
protection against ROP attacks, and can be viewed as part of a wider
trend to harden binaries.

It is similar to the option --enable-host-shared, except that --e-h-s
won't add -shared to the linker flags whereas --e-h-p will add -pie.
It is different from --enable-default-pie because that option just
adds an implicit -fPIE/-pie when the compiler is invoked, but the
compiler itself isn't PIE.

Since r12-5768-gfe7c3ecf, PCH works well with PIE, so there are no PCH
regressions.

When building the compiler, the build process may use various in-tree
libraries; these need to be built with -fPIE so that it's possible to
use them when building a PIE.  For instance, when --with-included-gettext
is in effect, intl object files must be compiled with -fPIE.  Similarly,
when building in-tree gmp, isl, mpfr and mpc, they must be compiled with
-fPIE.

I plan to add an option to link with -Wl,-z,now.

ChangeLog:

	* Makefile.def: Pass $(PICFLAG) to AM_CFLAGS for gmp, mpfr, mpc, and
	isl.
	* Makefile.in: Regenerate.
	* Makefile.tpl: Set PICFLAG.
	* configure.ac (--enable-host-pie): New check.  Set PICFLAG after this
	check.
	* configure: Regenerate.

c++tools/ChangeLog:

	* Makefile.in: Rename PIEFLAG to PICFLAG.  Set LD_PICFLAG.  Use it.
	Use pic/libiberty.a if PICFLAG is set.
	* configure.ac (--enable-default-pie): Set PICFLAG instead of PIEFLAG.
	(--enable-host-pie): New check.
	* configure: Regenerate.

fixincludes/ChangeLog:

	* Makefile.in: Set and use PICFLAG and LD_PICFLAG.  Use the "pic"
	build of libiberty if PICFLAG is set.
	* configure.ac:
	* configure: Regenerate.

gcc/ChangeLog:

	* Makefile.in: Set LD_PICFLAG.  Use it.  Set enable_host_pie.
	Remove NO_PIE_CFLAGS and NO_PIE_FLAG.  Pass LD_PICFLAG to
	ALL_LINKERFLAGS.  Use the "pic" build of libiberty if --enable-host-pie.
	* configure.ac (--enable-host-shared): Don't set PICFLAG here.
	(--enable-host-pie): New check.  Set PICFLAG and LD_PICFLAG after this
	check.
	* configure: Regenerate.
	* doc/install.texi: Document --enable-host-pie.

gcc/d/ChangeLog:

	* Make-lang.in: Remove NO_PIE_CFLAGS.

intl/ChangeLog:

	* Makefile.in: Use @PICFLAG@ in COMPILE as well.
	* configure.ac (--enable-host-shared): Don't set PICFLAG here.
	(--enable-host-pie): New check.  Set PICFLAG after this check.
	* configure: Regenerate.

libcody/ChangeLog:

	* Makefile.in: Pass LD_PICFLAG to LDFLAGS.
	* configure.ac (--enable-host-shared): Don't set PICFLAG here.
	(--enable-host-pie): New check.  Set PICFLAG and LD_PICFLAG after this
	check.
	* configure: Regenerate.

libcpp/ChangeLog:

	* configure.ac (--enable-host-shared): Don't set PICFLAG here.
	(--enable-host-pie): New check.  Set PICFLAG after this check.
	* configure: Regenerate.

libdecnumber/ChangeLog:

	* configure.ac (--enable-host-shared): Don't set PICFLAG here.
	(--enable-host-pie): New check.  Set PICFLAG after this check.
	* configure: Regenerate.

libiberty/ChangeLog:

	* configure.ac: Also set shared when enable_host_pie.
	* configure: Regenerate.

zlib/ChangeLog:

	* configure.ac (--enable-host-shared): Don't set PICFLAG here.
	(--enable-host-pie): New check.  Set PICFLAG after this check.
	* configure: Regenerate.

Needed after a recent change.

gcc/ChangeLog:

	* configure: Regenerate.

libatomic/ChangeLog:

	* configure: Regenerate.

libbacktrace/ChangeLog:

	* configure: Regenerate.

libcc1/ChangeLog:

	* configure: Regenerate.

libffi/ChangeLog:

	* configure: Regenerate.

libgfortran/ChangeLog:

	* configure: Regenerate.

libgomp/ChangeLog:

	* configure: Regenerate.

libitm/ChangeLog:

	* configure: Regenerate.

libobjc/ChangeLog:

	* configure: Regenerate.

liboffloadmic/ChangeLog:

	* configure: Regenerate.
	* plugin/configure: Regenerate.

libphobos/ChangeLog:

	* configure: Regenerate.

libquadmath/ChangeLog:

	* configure: Regenerate.

libsanitizer/ChangeLog:

	* configure: Regenerate.

libssp/ChangeLog:

	* configure: Regenerate.

libstdc++-v3/ChangeLog:

	* configure: Regenerate.

libvtv/ChangeLog:

	* configure: Regenerate.

lto-plugin/ChangeLog:

	* configure: Regenerate.

zlib/ChangeLog:

	* configure: Regenerate.

This change adds the configury bits to activate the build of
shared libs on VxWorks ports configured with --enable-shared,
for libraries variants where this is generally supported (rtp,
code model !large - currently not compatible with -fPIC).

Set lt_cv_deplibs_check_method in libtool.m4, so the build of
libraries know how to establish dependencies.  This is useful in
configurations such as aarch64 where proper support of LSE relies
on accurate dependency information between libstdc++ and libgcc_s
to begin with.

Regenerate configure scripts to reflect libtool.m4 change.

2022-10-09  Olivier Hainque  <hainque@adacore.com>

	* libtool.m4 (*vxworks*): When enable_shared, set dynamic_linker
	and friends for rtp !large. Assume the linker has the required
	abilities and set lt_cv_deplibs_check_method.

gcc/
	* config.gcc (*vxworks*): Add t-slibgcc fragment
	if enable_shared.

libgcc/
	* config.host (*vxworks*): When enable_shared, add
	libgcc and crtstuff "shared" fragments for rtp except
	large code model.
	(aarch64*-wrs-vxworks7*): Remove t-slibgcc-libgcc from
	the list of fragments.

2022-10-09  Olivier Hainque  <hainque@adacore.com>

gcc/
	* configure: Regenerate.

libatomic/
	* configure: Regenerate.

libbacktrace/
	* configure: Regenerate.

libcc1/
	* configure: Regenerate.

libffi/
	* configure: Regenerate.

libgfortran/
	* configure: Regenerate.

libgomp/
	* configure: Regenerate.

libitm/
	* configure: Regenerate.

libobjc/
	* configure: Regenerate.

liboffloadmic/
	* configure: Regenerate.

liboffloadmic/
	* plugin/configure: Regenerate.

libphobos/
	* configure: Regenerate.

libquadmath/
	* configure: Regenerate.

libsanitizer/
	* configure: Regenerate.

libssp/
	* configure: Regenerate.

libstdc++-v3/
	* configure: Regenerate.

libvtv/
	* configure: Regenerate.

lto-plugin/
	* configure: Regenerate.

zlib/
	* configure: Regenerate.

fixincludes/ChangeLog:

	* config.h.in: Regenerate.
	* configure: Regenerate.

libada/ChangeLog:

	* configure: Regenerate.

libiberty/ChangeLog:

	* configure: Regenerate.

libobjc/ChangeLog:

	* configure: Regenerate.

liboffloadmic/ChangeLog:

	* configure: Regenerate.
	* plugin/configure: Regenerate.

libquadmath/ChangeLog:

	* configure: Regenerate.

libssp/ChangeLog:

	* configure: Regenerate.

libvtv/ChangeLog:

	* configure: Regenerate.

zlib/ChangeLog:

	* configure: Regenerate.

This reverts commit bf8cdd35.

Sync with binutils for building binutils with LTO:

50ad1254d50 GCC: Pass --plugin to AR and RANLIB

Detect GCC LTO plugin.  Pass --plugin to AR and RANLIB to support LTO
build.

ChangeLog:

	* Makefile.tpl (AR): Add @AR_PLUGIN_OPTION@
	(RANLIB): Add @RANLIB_PLUGIN_OPTION@.
	* configure.ac: Include config/gcc-plugin.m4.
	AC_SUBST AR_PLUGIN_OPTION and RANLIB_PLUGIN_OPTION.
	* libtool.m4 (_LT_CMD_OLD_ARCHIVE): Pass --plugin to AR and
	RANLIB if possible.
	* Makefile.in: Regenerated.
	* configure: Likewise.

config/

	* gcc-plugin.m4 (GCC_PLUGIN_OPTION): New.

libiberty/

	* Makefile.in (AR): Add @AR_PLUGIN_OPTION@
	(RANLIB): Add @RANLIB_PLUGIN_OPTION@.
	(configure_deps): Depend on ../config/gcc-plugin.m4.
	* configure.ac: AC_SUBST AR_PLUGIN_OPTION and
	RANLIB_PLUGIN_OPTION.
	* aclocal.m4: Regenerated.
	* configure: Likewise.

zlib/

	* configure: Regenerated.

ChangeLog:

	* libtool.m4: Match gnu* along other GNU systems.
	* libgo/config/libtool.m4: Match gnu* along other GNU systems.
	* libgo/configure: Re-generate.

libffi/
	* configure: Re-generate.

libgomp/
	* configure: Re-generate.

gcc/

	* configure: Re-generate.

libatomic/

	* configure: Re-generate.

libbacktrace/

	* configure: Re-generate.

libcc1/

	* configure: Re-generate.

libgfortran/

	* configure: Re-generate.

libgomp/

	* configure: Re-generate.

libhsail-rt/

	* configure: Re-generate.

libitm/

	* configure: Re-generate.

libobjc/

	* configure: Re-generate.

liboffloadmic/

	* configure: Re-generate.
	* plugin/configure: Re-generate.

libphobos/

	* configure: Re-generate.

libquadmath/

	* configure: Re-generate.

libsanitizer/

	* configure: Re-generate.

libssp/

	* configure: Re-generate.

libstdc++-v3/

	* configure: Re-generate.

libvtv/

	* configure: Re-generate.

lto-plugin/

	* configure: Re-generate.

zlib/

	* configure: Re-generate.

The change in major version (and the increment from Darwin19 to 20)
caused libtool tests to fail which resulted in incorrect build settings
for shared libraries.

We take this opportunity to sort out the shared undefined symbols state
rather than propagating the current unsound behaviour into a new rev.

This change means that we default to the case that missing symbols are
considered an error, and if one wants to allow this intentionally, the
confiuration for that case should be set appropriately.

Three existing cases need undefined dynamic lookup:
 libitm, where there is already a configuration mechanism to add the
         flags.
 libcc1, where we add simple configuration to add the flags for Darwin.
 libsanitizer, where we can add to the existing extra flags.

libcc1/ChangeLog:

	PR target/97865
	* Makefile.am: Add dynamic_lookup to LD flags for Darwin.
	* configure.ac: Test for Darwin host and set a flag.
	* Makefile.in: Regenerate.
	* configure: Regenerate.

libitm/ChangeLog:

	PR target/97865
	* configure.tgt: Add dynamic_lookup to XLDFLAGS for Darwin.
	* configure: Regenerate.

libsanitizer/ChangeLog:

	PR target/97865
	* configure.tgt: Add dynamic_lookup to EXTRA_CXXFLAGS for
	Darwin.
	* configure: Regenerate.

ChangeLog:

	PR target/97865
	* libtool.m4: Update handling of Darwin platform link flags
	for Darwin20.

gcc/ChangeLog:

	PR target/97865
	* configure: Regenerate.

libatomic/ChangeLog:

	PR target/97865
	* configure: Regenerate.

libbacktrace/ChangeLog:

	PR target/97865
	* configure: Regenerate.

libffi/ChangeLog:

	PR target/97865
	* configure: Regenerate.

libgfortran/ChangeLog:

	PR target/97865
	* configure: Regenerate.

libgomp/ChangeLog:

	PR target/97865
	* configure: Regenerate.

libhsail-rt/ChangeLog:

	PR target/97865
	* configure: Regenerate.

libobjc/ChangeLog:

	PR target/97865
	* configure: Regenerate.

libphobos/ChangeLog:

	PR target/97865
	* configure: Regenerate.

libquadmath/ChangeLog:

	PR target/97865
	* configure: Regenerate.

libssp/ChangeLog:

	PR target/97865
	* configure: Regenerate.

libstdc++-v3/ChangeLog:

	PR target/97865
	* configure: Regenerate.

libvtv/ChangeLog:

	PR target/97865
	* configure: Regenerate.

zlib/ChangeLog:

	PR target/97865
	* configure: Regenerate.

This change adds the +nodefaultrpath ld option to remove all library
paths that were specified with the -L option from the embedded path.

2020-11-29  John David Anglin  <danglin@gcc.gnu.org>

ChangeLog:
	* libtool.m4 (archive_cmds): Add +nodefaultrpath ld option on
	hppa64-*-hpux11*.

libatomic/ChangeLog:
	* configure: Regenerate.

libbacktrace/ChangeLog:
	* configure: Regenerate.

libcc1/ChangeLog:
	* configure: Regenerate.

libffi/ChangeLog:
	* configure: Regenerate.

libgfortran/ChangeLog:
	* configure: Regenerate.

libgomp/ChangeLog:
	* configure: Regenerate.

libhsail-rt/ChangeLog:
	* configure: Regenerate.

libitm/ChangeLog:
	* configure: Regenerate.

libobjc/ChangeLog:
	* configure: Regenerate.

liboffloadmic/ChangeLog:
	* configure: Regenerate.
	* plugin/configure: Regenerate.

libquadmath/ChangeLog:
	* configure: Regenerate.

libsanitizer/ChangeLog:
	* configure: Regenerate.

libssp/ChangeLog:
	* configure: Regenerate.

libstdc++-v3/ChangeLog:
	* configure: Regenerate.

libvtv/ChangeLog:
	* configure: Regenerate.

lto-plugin/ChangeLog:
	* configure: Regenerate.

zlib/ChangeLog:
	* configure: Regenerate.

Avoid nested save_CFLAGS and save_LDFLAGS by replacing save_CFLAGS and
save_LDFLAGS with cet_save_CFLAGS and cet_save_LDFLAGS in cet.m4.

config/

	PR bootstrap/95413
	* cet.m4: Replace save_CFLAGS and save_LDFLAGS with
	cet_save_CFLAGS and cet_save_LDFLAGS.

gcc/

	PR bootstrap/95413
	* configure: Regenerated.

libatomic/

	PR bootstrap/95413
	* configure: Regenerated.

libbacktrace/

	PR bootstrap/95413
	* configure: Regenerated.

libcc1/

	PR bootstrap/95413
	* configure: Regenerated.

libcpp/

	PR bootstrap/95413
	* configure: Regenerated.

libdecnumber/

	PR bootstrap/95413
	* configure: Regenerated.

libgcc/

	PR bootstrap/95413
	* configure: Regenerated.

libgfortran/

	PR bootstrap/95413
	* configure: Regenerated.

libgomp/

	PR bootstrap/95413
	* configure: Regenerated.

libiberty/

	PR bootstrap/95413
	* configure: Regenerated.

libitm/

	PR bootstrap/95413
	* configure: Regenerated.

libobjc/

	PR bootstrap/95413
	* configure: Regenerated.

libphobos/

	PR bootstrap/95413
	* configure: Regenerated.

libquadmath/

	PR bootstrap/95413
	* configure: Regenerated.

libsanitizer/

	PR bootstrap/95413
	* configure: Regenerated.

libssp/

	PR bootstrap/95413
	* configure: Regenerated.

libstdc++-v3/

	PR bootstrap/95413
	* configure: Regenerated.

libvtv/

	PR bootstrap/95413
	* configure: Regenerated.

lto-plugin/

	PR bootstrap/95413
	* configure: Regenerated.

zlib/

	PR bootstrap/95413
	* configure: Regenerated.

When defaulting CET run-time support to auto, check if -fcf-protection
works.  Even if the stage1 GCC doesn't support -fcf-protection, since
the final GCC does, CET run-time support will be enabled by default if
binutils support CET.

config/

	PR bootstrap/95147
	* cet.m4 (GCC_CET_FLAGS): Also check if -fcf-protection works
	when defaulting to auto.

libatomic/

	PR bootstrap/95147
	* configure: Regenerated.

libbacktrace/

	PR bootstrap/95147
	* configure: Regenerated.

libgcc/

	PR bootstrap/95147
	* configure: Regenerated.

libgfortran/

	PR bootstrap/95147
	* configure: Regenerated.

libgomp/

	PR bootstrap/95147
	* configure: Regenerated.

libitm/

	PR bootstrap/95147
	* configure: Regenerated.

libobjc/

	PR bootstrap/95147
	* configure: Regenerated.

libphobos/

	PR bootstrap/95147
	* configure: Regenerated.

libquadmath/

	PR bootstrap/95147
	* configure: Regenerated.

libsanitizer/

	PR bootstrap/95147
	* configure: Regenerated.

libssp/

	PR bootstrap/95147
	* configure: Regenerated.

libstdc++-v3/

	PR bootstrap/95147
	* configure: Regenerated.

libvtv/

	PR bootstrap/95147
	* configure: Regenerated.

zlib/

	PR bootstrap/95147
	* configure: Regenerated.

CET has been added since GCC 8.  This patch defaults CET run-time support
to auto.  It enables CET run-time support if asssembler supports CET
instructions and multi-byte NOPs are enabled via SSE2.

config/

	* cet.m4 (GCC_CET_FLAGS): Change default to auto.

gcc/

	* configure: Regenerated.

libatomic/

	* configure: Regenerated.

libbacktrace/

	* configure: Regenerated.

libcc1/

	* configure: Regenerated.

libcpp/

	* configure: Regenerated.

libdecnumber/

	* configure: Regenerated.

libgcc/

	* configure: Regenerated.

libgfortran/

	* configure: Regenerated.

libgomp/

	* configure: Regenerated.

libitm/

	* configure: Regenerated.

libobjc/

	* configure: Regenerated.

libquadmath/

	* configure: Regenerated.

libsanitizer/

	* configure: Regenerated.

libssp/

	* configure: Regenerated.

libstdc++-v3/

	* configure: Regenerated.

libvtv/

	* configure: Regenerated.

zlib/

	* configure: Regenerated.

When --enable-cet is used to configure GCC, enable Intel CET in target
zlib.

	* Makefile.am (AM_CFLAGS): New.
	* configure.ac (CET_FLAGS): Add GCC_CET_FLAGS and AC_SUBST.
	* Makefile.in: Regenerated.
	* aclocal.m4: Likewise.
	* configure.ac: Likewise.

Provide means, in the form of a `--with-toolexeclibdir=' configuration
option, to override the default installation directory for target
libraries, otherwise known as $toolexeclibdir.  This is so that it is
possible to get newly-built libraries, particularly the shared ones,
installed in a common place, so that they can be readily used by the
target system as their host libraries, possibly over NFS, without a need
to manually copy them over from the currently hardcoded location they
would otherwise be installed in.

In the presence of the `--enable-version-specific-runtime-libs' option
and for configurations building native GCC the option is ignored.

	config/
	* toolexeclibdir.m4: New file.

	gcc/
	* doc/install.texi (Cross-Compiler-Specific Options): Document
	`--with-toolexeclibdir' option.

	libada/
	* Makefile.in (configure_deps): Add `toolexeclibdir.m4'.
	* configure.ac: Handle `--with-toolexeclibdir='.
	* configure: Regenerate.

	libatomic/
	* configure.ac: Handle `--with-toolexeclibdir='.
	* Makefile.in: Regenerate.
	* aclocal.m4: Regenerate.
	* configure: Regenerate.
	* testsuite/Makefile.in: Regenerate.

	libffi/
	* configure.ac: Handle `--with-toolexeclibdir='.
	* Makefile.in: Regenerate.
	* aclocal.m4: Regenerate.
	* configure: Regenerate.
	* include/Makefile.in: Regenerate.
	* man/Makefile.in: Regenerate.
	* testsuite/Makefile.in: Regenerate.

	libgcc/
	* Makefile.in (configure_deps): Add `toolexeclibdir.m4'.
	* configure.ac: Handle `--with-toolexeclibdir='.
	* configure: Regenerate.

	libgfortran/
	* configure.ac: Handle `--with-toolexeclibdir='.
	* Makefile.in: Regenerate.
	* aclocal.m4: Regenerate.
	* configure: Regenerate.

	libgomp/
	* configure.ac: Handle `--with-toolexeclibdir='.
	* Makefile.in: Regenerate.
	* aclocal.m4: Regenerate.
	* configure: Regenerate.
	* testsuite/Makefile.in: Regenerate.

	libhsail-rt/
	* configure.ac: Handle `--with-toolexeclibdir='.
	* Makefile.in: Regenerate.
	* aclocal.m4: Regenerate.
	* configure: Regenerate.

	libitm/
	* configure.ac: Handle `--with-toolexeclibdir='.
	* Makefile.in: Regenerate.
	* aclocal.m4: Regenerate.
	* configure: Regenerate.
	* testsuite/Makefile.in: Regenerate.

	libobjc/
	* Makefile.in (aclocal_deps): Add `toolexeclibdir.m4'.
	* aclocal.m4: Include `toolexeclibdir.m4'.
	* configure.ac: Handle `--with-toolexeclibdir='.
	* configure: Regenerate.

	liboffloadmic/
	* plugin/configure.ac: Handle `--with-toolexeclibdir='.
	* plugin/Makefile.in: Regenerate.
	* plugin/aclocal.m4: Regenerate.
	* plugin/configure: Regenerate.
	* configure.ac: Handle `--with-toolexeclibdir='.
	* Makefile.in: Regenerate.
	* aclocal.m4: Regenerate.
	* configure: Regenerate.

	libphobos/
	* m4/druntime.m4: Handle `--with-toolexeclibdir='.
	* m4/Makefile.in: Regenerate.
	* libdruntime/Makefile.in: Regenerate.
	* src/Makefile.in: Regenerate.
	* testsuite/Makefile.in: Regenerate.
	* Makefile.in: Regenerate.
	* aclocal.m4: Regenerate.
	* configure: Regenerate.

	libquadmath/
	* configure.ac: Handle `--with-toolexeclibdir='.
	* Makefile.in: Regenerate.
	* aclocal.m4: Regenerate.
	* configure: Regenerate.

	libsanitizer/
	* configure.ac: Handle `--with-toolexeclibdir='.
	* Makefile.in: Regenerate.
	* aclocal.m4: Regenerate.
	* configure: Regenerate.
	* asan/Makefile.in: Regenerate.
	* interception/Makefile.in: Regenerate.
	* libbacktrace/Makefile.in: Regenerate.
	* lsan/Makefile.in: Regenerate.
	* sanitizer_common/Makefile.in: Regenerate.
	* tsan/Makefile.in: Regenerate.
	* ubsan/Makefile.in: Regenerate.

	libssp/
	* configure.ac: Handle `--with-toolexeclibdir='.
	* Makefile.in: Regenerate.
	* aclocal.m4: Regenerate.
	* configure: Regenerate.

	libstdc++-v3/
	* acinclude.m4: Handle `--with-toolexeclibdir='.
	* Makefile.in: Regenerate.
	* aclocal.m4: Regenerate.
	* configure: Regenerate.
	* doc/Makefile.in: Regenerate.
	* include/Makefile.in: Regenerate.
	* libsupc++/Makefile.in: Regenerate.
	* po/Makefile.in: Regenerate.
	* python/Makefile.in: Regenerate.
	* src/Makefile.in: Regenerate.
	* src/c++11/Makefile.in: Regenerate.
	* src/c++17/Makefile.in: Regenerate.
	* src/c++98/Makefile.in: Regenerate.
	* src/filesystem/Makefile.in: Regenerate.
	* testsuite/Makefile.in: Regenerate.

	libvtv/
	* configure.ac: Handle `--with-toolexeclibdir='.
	* Makefile.in: Regenerate.
	* aclocal.m4: Regenerate.
	* configure: Regenerate.
	* testsuite/Makefile.in: Regenerate.

	zlib/
	* configure.ac: Handle `--with-toolexeclibdir='.
	* Makefile.in: Regenerate.
	* aclocal.m4: Regenerate.
	* configure: Regenerate.

A change made with r275564 ("[ARM/FDPIC v6 02/24] [ARM] FDPIC: Handle 
arm*-*-uclinuxfdpiceabi in configure scripts") to libtool.m4 has not 
regenerated all the `configure' scripts affected.  Fix it.

	gcc/
	* configure: Regenerate.

	libatomic/
	* configure: Regenerate.

	libbacktrace/
	* configure: Regenerate.

	libcc1/
	* configure: Regenerate.

	libffi/
	* configure: Regenerate.

	libgfortran/
	* configure: Regenerate.

	libgomp/
	* configure: Regenerate.

	libhsail-rt/
	* configure: Regenerate.

	libitm/
	* configure: Regenerate.

	libobjc/
	* configure: Regenerate.

	liboffloadmic/
	* configure: Regenerate.

	libphobos/
	* configure: Regenerate.

	libquadmath/
	* configure: Regenerate.

	libsanitizer/
	* configure: Regenerate.

	libssp/
	* configure: Regenerate.

	libstdc++-v3/
	* configure: Regenerate.

	libvtv/
	* configure: Regenerate.

	lto-plugin/
	* configure: Regenerate.

	zlib/
	* configure: Regenerate.

From-SVN: r276213

2019-01-21  Iain Buclaw  <ibuclaw@gdcproject.org>

	* Makefile.am (noinst_LTLIBRARIES): Rename libzgcj_convience.la to
	libz_convenience.la.
	* Makefile.in: Regenerate.
	* configure.ac: Remove target_all.
	* configure: Regenerate.

From-SVN: r268119